Decorating & Entertaining Ideas

Two Ways to Totally Transform Your Doors

Filed Under:

Our Weekend Decorator, Megan Pflug, is back with two insanely gorgeous DIY solutions to update your doors.

Project #1: Painted Door

One of the things I love about my bedroom is all the original molding on the walls. I toyed with painting the walls a color but settled on a clean fresh white to keep the look from getting too complicated. That being said, after a long winter, I decide to give my neutral palette an unexpected splash of color just in time for spring.  Keep reading for a few tips and tricks for a flawless paint job.

Here’s What You’ll Need:

  • 1 quart green paint (I used Benjamin Moore Granny Smith CSP-860 in semigloss)
  • 1 quart yellow paint (I used Benjamin Moore Fun ‘n Games 647 in semigloss)
  • Painter’s tape
  • Paintbrush


Tip: If you want to experiment with your own color combo for this project, pick out 10- 12 swatches, and try mixing and matching them until you get a combination you like.  You might be surprised at what looks good together.


Base Coat

Begin by painting the door all one color. I chose to start with the green because I knew I wanted my door to be mostly that color.

Tip: When painting a paneled door, start with the panel edges. Then paint the flat areas in long, even strokes.


Accent Color

Once the first coat of paint is dry, use your painter’s tape to mark off the area for your second color. To prevent seepage, smooth the tape edge in place with your finger. Begin applying paint to the taped seam first.  To ensure a crisp edge, brush the paint across the seam from the tape to the edge of the door, working in thin layers to prevent drips. After you have painted out the taped edge, move on to the panel edges, and finish by painting the flat areas, just as you did before. Now all that’s left is to carefully remove the painter’s tape and stand back to admire your work of art.

Shop the Look

Project #2: Upholstered Door

When I first moved into my circa-1910 row house in Brooklyn, all the doors were original to the building except one: the door to our home office. This anonymous-looking hollow-core door was totally out of sync with the rest of the house. So after some consideration I decided to turn lemons into lemonade and just embrace the fact that the door didn’t match.

The surface of the door was in pretty bad shape, so I figured that upholstering it would be the perfect solution. If nothing else it was a low-risk experiment because a new version of this kind of door runs only about $40 at the hardware store. It seemed easy enough, and I’m happy to report it actually was.  I gathered my supplies, including the leftover nail-head trim that I used in this closet makeover last spring, made a quick trip to the fabric store, and got started. Ready to find out how I hammered my way to a glamorous door?

Nail heads and trim from Zarin Fabrics. Paint, Benjamin Moore Tropical Teal 734. Green vinyl and felt from Online Fabric Store.

Nail heads and trim from Zarin Fabrics. Paint, Benjamin Moore Tropical Teal 734. Green vinyl and felt from Online Fabric Store.

Here’s What You’ll Need:

  • 3 yards of felt (does not need to be wool)
  • 3 yards of vinyl or other fabric
  • Magna-Tac Glue
  • Spray mount
  • Scissors
  • Box cutter or X-Acto knife
  • Nail-head trim and matching nail heads
  • Hammer
  • Latex paint
  • Paintbrush
  • Painter’s tape
  • Ruler


Before you get started it’s a good idea to remove the door from its frame and lay it flat.  You can remove most doors by pulling out the hinge pins; those are the little rods that join one side of the hinge to the other. I also recommend setting your door on an elevated surface, such as sawhorses, so that you don’t have to bend over while you’re working, but the ground is fine.


Getting Started

Begin by cutting out two layers of felt that are each 1 inch shorter and narrower than your door front.  Next, lightly mist the door’s surface with spray mount, and center one of the felt layers on top so that there is a 1-inch border of exposed door around all four edges. Then lightly mist the top of the felt you just put in place, and lay the second layer over the first.  The felt helps to give the finished product a slightly padded and dimensional look. An added bonus is that all these layers are great at dampening sound.

Tip: It’s important to keep the felt a little smaller than the door so it doesn’t add too much thickness along the edges, which could prevent your door from closing.


Attaching the Vinyl

Cut out a piece of vinyl about 2 inches longer and wider than your door. Apply a line of glue just outside the felt on all four edges of the door. Now lay the vinyl face up on the door, allowing the extra length and width to extend over the edges.  While the glue is still wet, press the vinyl into the glue. Once the vinyl is glued in place, trim the excess from the edges with a sharp box cutter so that the vinyl is flush with the sides of the door; you can do this by running the blade along the edge of the door.

Applying the Nail Heads

Don’t fret; I know the idea of hammering every single nail head into place is intimidating! That’s why I used a nail-head trim that you simply cut into strips and attach with a few single nail heads.  Here’s how I did it…


Mark Your Pattern

First I used painter’s tape and a ruler to mark where I wanted my nail-head rows. The good thing about using painter’s tape is that it allows you to make adjustments and see how the pattern will work before you start applying the nail heads. I choose to go around the outside edge and then create a diamond pattern on the inside, but the options are pretty much limitless.

Just be sure to keep the nail heads clear of the door molding and the knob hardware. A good rule of thumb is to start the nail heads one inch in from the outer edge of the door.  In my case the nail heads around the knob didn’t interfere, but if they do you could always skip a few inches to accommodate for a knob.

Once your design is all worked out, you’re ready to cut the trim to length and start hammering.  I used one length for each straight line of my pattern. To secure the corners I joined the two lengths of trim by overlapping the ends and hammering a single nail through both layers.

To finish the project I added a little turquoise paint to the edge of my door. Now all that’s left is to rehang your door and admire your work.  There you have it! Who knew upholstering a door could be so easy?

Shop the Look

Join the Discussion

Join the Discussion

Comments are closed.